PRODUCTS
Optimus 810
Chemical Resistant Adhesive & Caulking
Product Description
810 is a slowest version of the 810/820 series and has the same physical properties found in all of this series. The 810 is semi self-leveling and allows greater standing time and much more "spread time" than the 820. This heavy gel polymer compound is used as an adhesive for bonding various materials together and is highly resistant to fuels and other caustic compounds. The product can be sanded and painted and is also used as a filler for surface imperfections in various plastics and other substrates for rapid repairing and sealing of cracks or damaged areas. The product retains its flex even in thick applications, the product is not brittle, with good sand ability in a short time. The product is black or non-pigmented having a white tint when mixed properly and after it has set. 810 & 820 have no odor and are 100% solids.
Application
810 may be used directly from the dual cartridge unit or plural component pump. Mixing of the product is through a static mixer.
General Physical Characteristics
| Solids Hardness Mix Ratio Tensile (lb/mil) Color Viscosity cps @ 72°F Weight/gal Specific Gravity Gel Times Pot Life |
100% Shore D 60-63 1:1 2300 Natural or Black Part A: 1000+/-300 Part B: 1700+/-500 Part A: 9.52+/-0.2 Part B: 8.9+/-0.2 1.08 6-10 min. @ 75°F 4-6 minutes @ 75°F |
**Gel Time is temperature dependent, the product will set considerably faster in warm or hot conditions and slower in cool conditions.
Advantages
High chemical resistance, fuel resistant.
Highly adhesive to many substrates
Good working time, quick gel time, trowel-able
Bonds to plastic, urethane, polyurea, fiberglass, steel, wood and concrete
Cartridge dispensed
Can be sanded and painted
Designed to seal plastic connectors, fittings, concrete floor cracks, etc. against severe chemical and physical environments, traffic, abrasion, thermal shock and corrosive fumes, steam & hot water
Use Areas
Fiberglass bonding and repair
Tank seam sealing
Food processing areas – floor repair
Vertical Surfaces – sealing and repair
Used as caulking, filling, bonding and self-leveling applications
Waste holding & treatment areas – sealing and repair
Petrochemical production floors
Pulp and paper
Waste Treatment facilities
High traffic industrial floors
Used for immediate crack and damage repair for decorative floors
Surface Preparation: Surface is to be free of all contaminants that would act as a bond breaker. The area to be sealed should be sound to the degree that good bonding of the product will result when properly applied. The area should be dry.
Curing Time: Back in service time –traffic- 1 to 1.5 hours approximately. Re-coat 30 minutes to 45 minutes @ 70°F. Full cure in 6 to 8 hours @ 70°F.
Concrete: Must be cured at least 28 days. All surfaces must be dry and dust free.
Shelf Life: Six Months, store between 70°F and 90°F.
Packaging: Packaging: 21 and 54 ounce duplex cartridge kits, 10 gallon kits (5 gallon pails) and 110 gallon kits (55 gallons per drum).
VOC Content: 0gms/1 or 0.0 lbs/gal
Limitations: Do use on wet surfaces or expose part A to moisture. Keep out of direct sunlight, store at room temperature. Do not allow the product to stand in the static mixer. Use at 5 degrees F above dew point. Keep cartridges warm when using product in cool conditions.
*Do not expose boxes of cartridges to sunlight or store in hot areas as this will accelerate gel time. Important: Hot conditions will speed the set time of the product, while cool conditions will slow the set time.
This product is for use by professional applicators only. Wear Protective Clothing. Read MSDS before using this product. DOT/Flash Point – Non-flammable Liquid Classification, not regulated.
Modular Fiberglass Tank Bonding
Fiberglass Sumps – modular tank sections bonded in the field with Madison’s 810 series product.
810 – slow system, duplex cartridges, high chemical resistance applied using a pneumatic duplex gun. Set time approximately 5 to 8 minutes.
Clean channel, abrade as needed apply 810, moving quickly around the perimeter of the tank.
Clean channel, abrade as needed apply 810, moving quickly around the perimeter of the tank.
Clean channel, abrade as needed apply 810, moving quickly around the perimeter of the tank.
Clean channel, abrade as needed apply 810, moving quickly around the perimeter of the tank.
